Linux version 2.6.9-11.EL (bhcompile@boris.devel.redhat.com) (gcc version 3.4.3 20050227 (Red Hat 3.4.3-22)) #1 SMP Fri May 20 18:25:13 EDT 2005 EFI v1.10 by HP: SALsystab=0x703ff83a970 ACPI 2.0=0x703ff040000 HCDP=0x703ff078020 SMBIOS=0x7fffc000 booting generic kernel on platform hpzx1 ACPI: RSDP (v002 HP ) @ 0x00000703ff040000 ACPI: XSDT (v001 HP rx8620 0x00000000 HP 0x00000000) @ 0x00000703ff05eea0 ACPI: FADT (v003 HP rx8620 0x00000000 HP 0x00000000) @ 0x00000703ff05eb10 ACPI: SPCR (v001 HP rx8620 0x00000000 HP 0x00000000) @ 0x00000703ff040068 ACPI: DBGP (v001 HP rx8620 0x00000000 HP 0x00000000) @ 0x00000703ff0400b8 ACPI: MADT (v001 HP rx8620 0x00000000 HP 0x00000000) @ 0x00000703ff0401a0 ACPI: SLIT (v001 HP rx8620 0x00000000 HP 0x00000000) @ 0x00000703ff05ec08 ACPI: CPEP (v001 HP rx8620 0x00000000 HP 0x00000000) @ 0x00000703ff05ec48 ACPI: SRAT (v001 HP rx8620 0x00000000 HP 0x00000000) @ 0x00000703ff05ecf8 ACPI: SPMI (v004 HP rx8620 0x00000000 HP 0x00000000) @ 0x00000703ff05eac0 ACPI: OEMD (v001 HP rx8620 0x00000000 HP 0x00000000) @ 0x00000703ff040128 ACPI: HPET (v001 HP rx8620 0x00000000 HP 0x00000000) @ 0x00000703ff0400f0 ACPI: SSDT (v002 HP CELL001 0x00000000 HP 0x00000000) @ 0x00000703ff05ef90 ACPI: SSDT (v002 HP CELL002 0x00000000 HP 0x00000000) @ 0x00000703ff076340 ACPI: SSDT (v002 HP CELL003 0x00000000 HP 0x00000000) @ 0x00000703ff0771b0 ACPI: DSDT (v002 HP CELL000 0x00000000 HP 0x00000000) @ 0x0000000000000000 Number of logical nodes in system = 5 Number of memory chunks in system = 3 warning: skipping physical page 0 warning: skipping physical page 0 warning: skipping physical page 0 Initial ramdisk at: 0xe0000040fedc9000 (1904334 bytes) SAL 3.1: HP Orca/IPF version 1.22 SAL Platform features: None SAL: AP wakeup using external interrupt vector 0xff ACPI: Local APIC address c0000000fee00000 GSI 16 (level, low) -> CPU 0 (0x0000) vector 48 16 CPUs available, 16 CPUs total PCDP: v1 at 0xe0000703ff078020 PCDP: serial console at MMIO 0xf0000019000 (ttyS0, options 9600n8) MCA related initialization done warning: skipping physical page 0 Virtual mem_map starts at 0xa0007fffc7200000 On node 0 totalpages: 4189383 DMA zone: 4189383 pages, LIFO batch:4 Normal zone: 0 pages, LIFO batch:1 HighMem zone: 0 pages, LIFO batch:1 Built 1 zonelists Kernel command line: BOOT_IMAGE=scsi0:EFI\redhat\vmlinuz-2.6.9-11.EL console=ttyS0,9600n8 rhgb quiet root=LABEL=/1 ro PID hash table entries: 4096 (order: 12, 131072 bytes) CPU 0: base freq=200.000MHz, ITC ratio=15/2, ITC freq=1500.000MHz+/--1ppm Console: colour dummy device 80x25 Dentry cache hash table entries: 8388608 (order: 12, 67108864 bytes) Inode-cache hash table entries: 4194304 (order: 11, 33554432 bytes) Memory: 66695040k/67030128k available (5476k code, 347088k reserved, 2192k data, 384k init) McKinley Errata 9 workaround not needed; disabling it Calibrating delay loop... 2241.08 BogoMIPS (lpj=1093632) Security Scaffold v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode There is already a security framework initialized, register_security failed. selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 1024 (order: 0, 16384 bytes) Boot processor id 0x0/0x0 task migration cache decay timeout: 10 msecs. CPU 1: synchronized ITC with CPU 0 (last diff 8 cycles, maxerr 717 cycles) CPU 1: base freq=200.000MHz, ITC ratio=15/2, ITC freq=1500.000MHz+/--1ppm Calibrating delay loop... 2241.08 BogoMIPS (lpj=1093632) CPU 2: synchronized ITC with CPU 0 (last diff -2 cycles, maxerr 2630 cycles) CPU 2: base freq=200.000MHz, ITC ratio=15/2, ITC freq=1500.000MHz+/--1ppm Calibrating delay loop... 2241.08 BogoMIPS (lpj=1093632) CPU 3: synchronized ITC with CPU 0 (last diff 0 cycles, maxerr 2630 cycles) CPU 3: base freq=200.000MHz, ITC ratio=15/2, ITC freq=1500.000MHz+/--1ppm Calibrating delay loop... 2241.08 BogoMIPS (lpj=1093632) CPU 4: synchronized ITC with CPU 0 (last diff 0 cycles, maxerr 2588 cycles) CPU 4: base freq=200.000MHz, ITC ratio=15/2, ITC freq=1500.000MHz+/--1ppm Calibrating delay loop... 2241.08 BogoMIPS (lpj=1093632) CPU 5: synchronized ITC with CPU 0 (last diff -1 cycles, maxerr 2588 cycles) CPU 5: base freq=200.000MHz, ITC ratio=15/2, ITC freq=1500.000MHz+/--1ppm Calibrating delay loop... 2241.08 BogoMIPS (lpj=1093632) CPU 6: synchronized ITC with CPU 0 (last diff -7 cycles, maxerr 2588 cycles) CPU 6: base freq=200.000MHz, ITC ratio=15/2, ITC freq=1500.000MHz+/--1ppm Calibrating delay loop... 2241.08 BogoMIPS (lpj=1093632) CPU 7: synchronized ITC with CPU 0 (last diff -7 cycles, maxerr 2588 cycles) CPU 7: base freq=200.000MHz, ITC ratio=15/2, ITC freq=1500.000MHz+/--1ppm Calibrating delay loop... 2241.08 BogoMIPS (lpj=1093632) CPU 8: synchronized ITC with CPU 0 (last diff 0 cycles, maxerr 2990 cycles) CPU 8: base freq=200.000MHz, ITC ratio=15/2, ITC freq=1500.000MHz+/--1ppm Calibrating delay loop... 2241.08 BogoMIPS (lpj=1093632) CPU 9: synchronized ITC with CPU 0 (last diff -6 cycles, maxerr 2985 cycles) CPU 9: base freq=200.000MHz, ITC ratio=15/2, ITC freq=1500.000MHz+/--1ppm Calibrating delay loop... 2241.08 BogoMIPS (lpj=1093632) CPU 10: synchronized ITC with CPU 0 (last diff 0 cycles, maxerr 2990 cycles) CPU 10: base freq=200.000MHz, ITC ratio=15/2, ITC freq=1500.000MHz+/--1ppm Calibrating delay loop... 2241.08 BogoMIPS (lpj=1093632) CPU 11: synchronized ITC with CPU 0 (last diff -11 cycles, maxerr 2978 cycles) CPU 11: base freq=200.000MHz, ITC ratio=15/2, ITC freq=1500.000MHz+/--1ppm Calibrating delay loop... 2241.08 BogoMIPS (lpj=1093632) CPU 12: synchronized ITC with CPU 0 (last diff -15 cycles, maxerr 3002 cycles) CPU 12: base freq=200.000MHz, ITC ratio=15/2, ITC freq=1500.000MHz+/--1ppm Calibrating delay loop... 2241.08 BogoMIPS (lpj=1093632) CPU 13: synchronized ITC with CPU 0 (last diff -9 cycles, maxerr 2990 cycles) CPU 13: base freq=200.000MHz, ITC ratio=15/2, ITC freq=1500.000MHz+/--1ppm Calibrating delay loop... 2241.08 BogoMIPS (lpj=1093632) CPU 14: synchronized ITC with CPU 0 (last diff -2 cycles, maxerr 2990 cycles) CPU 14: base freq=200.000MHz, ITC ratio=15/2, ITC freq=1500.000MHz+/--1ppm Calibrating delay loop... 2241.08 BogoMIPS (lpj=1093632) CPU 15: synchronized ITC with CPU 0 (last diff 2 cycles, maxerr 2978 cycles) CPU 15: base freq=200.000MHz, ITC ratio=15/2, ITC freq=1500.000MHz+/--1ppm Calibrating delay loop... 2241.08 BogoMIPS (lpj=1093632) Brought up 16 CPUs Total of 16 processors activated (35856.28 BogoMIPS). checking if image is initramfs... it is Freeing initrd memory: 1840kB freed NET: Registered protocol family 16 ACPI: Subsystem revision 20040816 ACPI: Interpreter enabled ACPI: Using IOSAPIC for interrupt routing ACPI: PCI Root Bridge [L000] (00:00) ACPI: PCI Interrupt Routing Table [\_SB_.N000.S000.IOC0.L000._PRT] ACPI: PCI Root Bridge [L001] (00:08) ACPI: PCI Interrupt Routing Table [\_SB_.N000.S000.IOC0.L001._PRT] ACPI: PCI Root Bridge [L002] (00:10) ACPI: PCI Interrupt Routing Table [\_SB_.N000.S000.IOC0.L002._PRT] ACPI: PCI Root Bridge [L004] (00:20) ACPI: PCI Interrupt Routing Table [\_SB_.N000.S000.IOC0.L004._PRT] ACPI: PCI Root Bridge [L006] (00:30) ACPI: PCI Interrupt Routing Table [\_SB_.N000.S000.IOC0.L006._PRT] ACPI: PCI Root Bridge [L008] (00:40) ACPI: PCI Interrupt Routing Table [\_SB_.N000.S000.IOC1.L008._PRT] ACPI: PCI Root Bridge [L010] (00:50) ACPI: PCI Interrupt Routing Table [\_SB_.N000.S000.IOC1.L010._PRT] ACPI: PCI Root Bridge [L012] (00:60) ACPI: PCI Interrupt Routing Table [\_SB_.N000.S000.IOC1.L012._PRT] ACPI: PCI Root Bridge [L014] (00:70) ACPI: PCI Interrupt Routing Table [\_SB_.N000.S000.IOC1.L014._PRT] ACPI: PCI Root Bridge [L000] (01:00) ACPI: PCI Interrupt Routing Table [\_SB_.N001.S016.IOC0.L000._PRT] ACPI: PCI Root Bridge [L001] (01:08) ACPI: PCI Interrupt Routing Table [\_SB_.N001.S016.IOC0.L001._PRT] ACPI: PCI Root Bridge [L002] (01:10) ACPI: PCI Interrupt Routing Table [\_SB_.N001.S016.IOC0.L002._PRT] ACPI: PCI Root Bridge [L004] (01:20) ACPI: PCI Interrupt Routing Table [\_SB_.N001.S016.IOC0.L004._PRT] ACPI: PCI Root Bridge [L006] (01:30) ACPI: PCI Interrupt Routing Table [\_SB_.N001.S016.IOC0.L006._PRT] ACPI: PCI Root Bridge [L008] (01:40) ACPI: PCI Interrupt Routing Table [\_SB_.N001.S016.IOC1.L008._PRT] ACPI: PCI Root Bridge [L010] (01:50) ACPI: PCI Interrupt Routing Table [\_SB_.N001.S016.IOC1.L010._PRT] ACPI: PCI Root Bridge [L012] (01:60) ACPI: PCI Interrupt Routing Table [\_SB_.N001.S016.IOC1.L012._PRT] ACPI: PCI Root Bridge [L014] (01:70) ACPI: PCI Interrupt Routing Table [\_SB_.N001.S016.IOC1.L014._PRT] usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing GSI 29 (level, low) -> CPU 1 (0x0400) vector 49 ACPI: PCI interrupt 0000:00:00.0[A] -> GSI 29 (level, low) -> IRQ 49 ACPI: PCI interrupt 0000:00:00.1[A] -> GSI 29 (level, low) -> IRQ 49 GSI 28 (level, low) -> CPU 2 (0x0800) vector 50 ACPI: PCI interrupt 0000:00:01.0[A] -> GSI 28 (level, low) -> IRQ 50 GSI 24 (level, low) -> CPU 3 (0x0c00) vector 51 ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 24 (level, low) -> IRQ 51 GSI 25 (level, low) -> CPU 4 (0x0001) vector 52 ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 25 (level, low) -> IRQ 52 GSI 26 (level, low) -> CPU 5 (0x0401) vector 53 ACPI: PCI interrupt 0000:00:03.0[A] -> GSI 26 (level, low) -> IRQ 53 GSI 27 (level, low) -> CPU 6 (0x0801) vector 54 ACPI: PCI interrupt 0000:00:03.1[B] -> GSI 27 (level, low) -> IRQ 54 GSI 76 (level, low) -> CPU 7 (0x0c01) vector 55 ACPI: PCI interrupt 0000:40:01.0[A] -> GSI 76 (level, low) -> IRQ 55 GSI 77 (level, low) -> CPU 8 (0x0002) vector 56 ACPI: PCI interrupt 0000:40:01.1[B] -> GSI 77 (level, low) -> IRQ 56 GSI 133 (level, low) -> CPU 9 (0x0402) vector 57 ACPI: PCI interrupt 0001:00:00.0[A] -> GSI 133 (level, low) -> IRQ 57 ACPI: PCI interrupt 0001:00:00.1[A] -> GSI 133 (level, low) -> IRQ 57 GSI 132 (level, low) -> CPU 10 (0x0802) vector 58 ACPI: PCI interrupt 0001:00:01.0[A] -> GSI 132 (level, low) -> IRQ 58 GSI 128 (level, low) -> CPU 11 (0x0c02) vector 59 ACPI: PCI interrupt 0001:00:02.0[A] -> GSI 128 (level, low) -> IRQ 59 GSI 129 (level, low) -> CPU 12 (0x0003) vector 60 ACPI: PCI interrupt 0001:00:02.1[B] -> GSI 129 (level, low) -> IRQ 60 GSI 130 (level, low) -> CPU 13 (0x0403) vector 61 ACPI: PCI interrupt 0001:00:03.0[A] -> GSI 130 (level, low) -> IRQ 61 GSI 131 (level, low) -> CPU 14 (0x0803) vector 62 ACPI: PCI interrupt 0001:00:03.1[B] -> GSI 131 (level, low) -> IRQ 62 GSI 180 (level, low) -> CPU 15 (0x0c03) vector 63 ACPI: PCI interrupt 0001:40:01.0[A] -> GSI 180 (level, low) -> IRQ 63 GSI 181 (level, low) -> CPU 0 (0x0000) vector 64 ACPI: PCI interrupt 0001:40:01.1[B] -> GSI 181 (level, low) -> IRQ 64 IOC: sx1000 0.1 HPA 0xf8020002000 IOVA space 1024Mb at 0x80000000 IOC: sx1000 0.1 HPA 0xf8020003000 IOVA space 1024Mb at 0x80000000 IOC: sx1000 0.1 HPA 0xf8120002000 IOVA space 1024Mb at 0x80000000 IOC: sx1000 0.1 HPA 0xf8120003000 IOVA space 1024Mb at 0x80000000 perfmon: version 2.0 IRQ 238 perfmon: Itanium 2 PMU detected, 16 PMCs, 18 PMDs, 4 counters (47 bits) PAL Information Facility v0.5 perfmon: added sampling format default_format perfmon_default_smpl: default_format v2.0 registered audit: initializing netlink socket (disabled) audit(1119014074.010:0): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 2048 (order 0, 16384 bytes) SELinux: Registering netfilter hooks Initializing Cryptographic API ksign: Installing public key data Loading keyring - Added public key 8F3E08D12180B66E - User ID: Red Hat, Inc. (Kernel Module GPG key) pci_hotplug: PCI Hot Plug PCI Core version: 0.5 ACPI: Processor [P000] (supports C1) ACPI: Processor [P002] (supports C1) ACPI: Processor [P004] (supports C1) ACPI: Processor [P006] (supports C1) ACPI: Processor [P008] (supports C1) ACPI: Processor [P010] (supports C1) ACPI: Processor [P012] (supports C1) ACPI: Processor [P014] (supports C1) ACPI: Processor [P016] (supports C1) ACPI: Processor [P018] (supports C1) ACPI: Processor [P020] (supports C1) ACPI: Processor [P022] (supports C1) ACPI: Processor [P024] (supports C1) ACPI: Processor [P026] (supports C1) ACPI: Processor [P028] (supports C1) ACPI: Processor [P030] (supports C1) EFI Time Services Driver v0.4 Linux agpgart interface v0.100 (c) Dave Jones i8042.c: i8042 controller self test timeout. Serial: 8250/16550 driver $Revision: 1.90 $ 20 ports, IRQ sharing enabled ttyS0 at MMIO 0xf0000019000 (irq = 49) is a 16550A ACPI: PCI interrupt 0000:00:00.0[A] -> GSI 29 (level, low) -> IRQ 49 ttyS1 at MMIO 0xf0000018000 (irq = 49) is a 16550A ACPI: PCI interrupt 0000:00:00.1[A] -> GSI 29 (level, low) -> IRQ 49 ttyS2 at MMIO 0xf0000019010 (irq = 49) is a 16550A ttyS3 at MMIO 0xf0000019038 (irq = 49) is a 16550A ACPI: PCI interrupt 0001:00:00.0[A] -> GSI 133 (level, low) -> IRQ 57 ttyS4 at MMIO 0xf0100018000 (irq = 57) is a 16450 ACPI: PCI interrupt 0001:00:00.1[A] -> GSI 133 (level, low) -> IRQ 57 ttyS5 at MMIO 0xf0100019000 (irq = 57) is a 16550A ttyS6 at MMIO 0xf0100019010 (irq = 57) is a 16550A ttyS7 at MMIO 0xf0100019038 (irq = 57) is a 16550A RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize divert: not allocating divert_blk for non-ethernet device lo Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Probing IDE interface ide0... Probing IDE interface ide1... Probing IDE interface ide2... Probing IDE interface ide3... Probing IDE interface ide4... Probing IDE interface ide5... ide-floppy driver 0.99.newide usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.0:USB HID core driver mice: PS/2 mouse device common for all mice md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 EFI Variables Facility v0.08 2004-May-17 NET: Registered protocol family 2 IP: routing cache hash table of 1048576 buckets, 16384Kbytes TCP: Hash tables configured (established 33554432 bind 65536) Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 Freeing unused kernel memory: 384kB freed SCSI subsystem initialized ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 24 (level, low) -> IRQ 51 sym0: <1010-66> rev 0x1 at pci 0000:00:02.0 irq 51 sym0: using 64 bit DMA addressing sym0: Symbios NVRAM, ID 7, Fast-80, SE, parity checking sym0: open drain IRQ line driver, using on-chip SRAM sym0: using LOAD/STORE-based firmware. sym0: handling phase mismatch from SCRIPTS. sym0: SCSI BUS has been reset. scsi0 : sym-2.1.18j Using cfq io scheduler Vendor: HP 146 G Model: MAP3147NC Rev: HPC6 Type: Direct-Access ANSI SCSI revision: 03 sym0:6:0: tagged command queuing enabled, command queue depth 16. target0:0:6: Beginning Domain Validation sym0:6: wide asynchronous. sym0:6: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 31) target0:0:6: Ending Domain Validation SCSI device sda: 286749488 512-byte hdwr sectors (146816 MB) SCSI device sda: drive cache: write through sda: sda1 sda2 sda3 sda4 sda5 sda6 sda7 Attached scsi disk sda at scsi0, channel 0, id 6, lun 0 ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 25 (level, low) -> IRQ 52 sym1: <1010-66> rev 0x1 at pci 0000:00:02.1 irq 52 sym1: using 64 bit DMA addressing sym1: Symbios NVRAM, ID 7, Fast-80, SE, parity checking sym1: open drain IRQ line driver, using on-chip SRAM sym1: using LOAD/STORE-based firmware. sym1: handling phase mismatch from SCRIPTS. sym1: SCSI BUS has been reset. scsi1 : sym-2.1.18j Vendor: _NEC Model: DVD+RW ND-2100AD Rev: 1.28 Type: CD-ROM ANSI SCSI revision: 02 target1:0:2: Beginning Domain Validation sym1:2: wide asynchronous. sym1:2: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 14) target1:0:2: Domain Validation skipping write tests target1:0:2: Ending Domain Validation ACPI: PCI interrupt 0000:00:03.0[A] -> GSI 26 (level, low) -> IRQ 53 sym2: <1010-66> rev 0x1 at pci 0000:00:03.0 irq 53 sym2: using 64 bit DMA addressing sym2: Symbios NVRAM, ID 7, Fast-80, SE, parity checking sym2: open drain IRQ line driver, using on-chip SRAM sym2: using LOAD/STORE-based firmware. sym2: handling phase mismatch from SCRIPTS. sym2: SCSI BUS has been reset. scsi2 : sym-2.1.18j Vendor: HP 146 G Model: MAP3147NC Rev: HPC6 Type: Direct-Access ANSI SCSI revision: 03 sym2:6:0: tagged command queuing enabled, command queue depth 16. target2:0:6: Beginning Domain Validation sym2:6: wide asynchronous. sym2:6: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 31) target2:0:6: Ending Domain Validation SCSI device sdb: 286749488 512-byte hdwr sectors (146816 MB) SCSI device sdb: drive cache: write through sdb: Attached scsi disk sdb at scsi2, channel 0, id 6, lun 0 ACPI: PCI interrupt 0000:00:03.1[B] -> GSI 27 (level, low) -> IRQ 54 sym3: <1010-66> rev 0x1 at pci 0000:00:03.1 irq 54 sym3: using 64 bit DMA addressing sym3: Symbios NVRAM, ID 7, Fast-80, LVD, parity checking sym3: open drain IRQ line driver, using on-chip SRAM sym3: using LOAD/STORE-based firmware. sym3: handling phase mismatch from SCRIPTS. sym3: SCSI BUS has been reset. scsi3 : sym-2.1.18j ACPI: PCI interrupt 0001:00:02.0[A] -> GSI 128 (level, low) -> IRQ 59 sym4: <1010-66> rev 0x1 at pci 0001:00:02.0 irq 59 sym4: using 64 bit DMA addressing sym4: Symbios NVRAM, ID 7, Fast-80, SE, parity checking sym4: open drain IRQ line driver, using on-chip SRAM sym4: using LOAD/STORE-based firmware. sym4: handling phase mismatch from SCRIPTS. sym4: SCSI BUS has been reset. scsi4 : sym-2.1.18j Vendor: HP 146 G Model: MAP3147NC Rev: HPC6 Type: Direct-Access ANSI SCSI revision: 03 sym4:6:0: tagged command queuing enabled, command queue depth 16. target4:0:6: Beginning Domain Validation sym4:6: wide asynchronous. sym4:6: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 31) target4:0:6: Ending Domain Validation SCSI device sdc: 286749488 512-byte hdwr sectors (146816 MB) SCSI device sdc: drive cache: write through sdc: Attached scsi disk sdc at scsi4, channel 0, id 6, lun 0 ACPI: PCI interrupt 0001:00:02.1[B] -> GSI 129 (level, low) -> IRQ 60 sym5: <1010-66> rev 0x1 at pci 0001:00:02.1 irq 60 sym5: using 64 bit DMA addressing sym5: Symbios NVRAM, ID 7, Fast-80, SE, parity checking sym5: open drain IRQ line driver, using on-chip SRAM sym5: using LOAD/STORE-based firmware. sym5: handling phase mismatch from SCRIPTS. sym5: SCSI BUS has been reset. scsi5 : sym-2.1.18j ACPI: PCI interrupt 0001:00:03.0[A] -> GSI 130 (level, low) -> IRQ 61 sym6: <1010-66> rev 0x1 at pci 0001:00:03.0 irq 61 sym6: using 64 bit DMA addressing sym6: Symbios NVRAM, ID 7, Fast-80, SE, parity checking sym6: open drain IRQ line driver, using on-chip SRAM sym6: using LOAD/STORE-based firmware. sym6: handling phase mismatch from SCRIPTS. sym6: SCSI BUS has been reset. scsi6 : sym-2.1.18j Vendor: HP 146 G Model: MAP3147NC Rev: HPC6 Type: Direct-Access ANSI SCSI revision: 03 sym6:6:0: tagged command queuing enabled, command queue depth 16. target6:0:6: Beginning Domain Validation sym6:6: wide asynchronous. sym6:6: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 31) target6:0:6: Ending Domain Validation SCSI device sdd: 286749488 512-byte hdwr sectors (146816 MB) SCSI device sdd: drive cache: write through sdd: sdd1 sdd2 sdd3 Attached scsi disk sdd at scsi6, channel 0, id 6, lun 0 ACPI: PCI interrupt 0001:00:03.1[B] -> GSI 131 (level, low) -> IRQ 62 sym7: <1010-66> rev 0x1 at pci 0001:00:03.1 irq 62 sym7: using 64 bit DMA addressing sym7: Symbios NVRAM, ID 7, Fast-80, LVD, parity checking sym7: open drain IRQ line driver, using on-chip SRAM sym7: using LOAD/STORE-based firmware. sym7: handling phase mismatch from SCRIPTS. sym7: SCSI BUS has been reset. scsi7 : sym-2.1.18j QLogic Fibre Channel HBA Driver (a0000002001ab980) ACPI: PCI interrupt 0000:40:01.0[A] -> GSI 76 (level, low) -> IRQ 55 qla2300 0000:40:01.0: Found an ISP2312, irq 55, iobase 0xc0000f4000040000 qla2300 0000:40:01.0: Configuring PCI space... qla2300 0000:40:01.0: Configure NVRAM parameters... qla2300 0000:40:01.0: Verifying loaded RISC code... qla2300 0000:40:01.0: Waiting for LIP to complete... qla2300 0000:40:01.0: Cable is unplugged... scsi8 : qla2xxx qla2300 0000:40:01.0: QLogic Fibre Channel HBA Driver: 8.00.00b21-k QLogic HP A6826-60001 - ISP2312: PCI-X (133 MHz) @ 0000:40:01.0 hdma+, host#=8, fw=3.03.02 IPX ACPI: PCI interrupt 0000:40:01.1[B] -> GSI 77 (level, low) -> IRQ 56 qla2300 0000:40:01.1: Found an ISP2312, irq 56, iobase 0xc0000f4000041000 qla2300 0000:40:01.1: Configuring PCI space... qla2300 0000:40:01.1: Configure NVRAM parameters... qla2300 0000:40:01.1: Verifying loaded RISC code... qla2300 0000:40:01.1: Waiting for LIP to complete... qla2300 0000:40:01.1: Cable is unplugged... scsi9 : qla2xxx qla2300 0000:40:01.1: QLogic Fibre Channel HBA Driver: 8.00.00b21-k QLogic HP A6826-60001 - ISP2312: PCI-X (133 MHz) @ 0000:40:01.1 hdma+, host#=9, fw=3.03.02 IPX ACPI: PCI interrupt 0001:40:01.0[A] -> GSI 180 (level, low) -> IRQ 63 qla2300 0001:40:01.0: Found an ISP2312, irq 63, iobase 0xc0000f4100040000 qla2300 0001:40:01.0: Configuring PCI space... qla2300 0001:40:01.0: Configure NVRAM parameters... qla2300 0001:40:01.0: Verifying loaded RISC code... qla2300 0001:40:01.0: Waiting for LIP to complete... qla2300 0001:40:01.0: Cable is unplugged... scsi10 : qla2xxx qla2300 0001:40:01.0: QLogic Fibre Channel HBA Driver: 8.00.00b21-k QLogic HP A6826-60001 - ISP2312: PCI-X (133 MHz) @ 0001:40:01.0 hdma+, host#=10, fw=3.03.02 IPX ACPI: PCI interrupt 0001:40:01.1[B] -> GSI 181 (level, low) -> IRQ 64 qla2300 0001:40:01.1: Found an ISP2312, irq 64, iobase 0xc0000f4100041000 qla2300 0001:40:01.1: Configuring PCI space... qla2300 0001:40:01.1: Configure NVRAM parameters... qla2300 0001:40:01.1: Verifying loaded RISC code... qla2300 0001:40:01.1: Waiting for LIP to complete... qla2300 0001:40:01.1: Cable is unplugged... scsi11 : qla2xxx qla2300 0001:40:01.1: QLogic Fibre Channel HBA Driver: 8.00.00b21-k QLogic HP A6826-60001 - ISP2312: PCI-X (133 MHz) @ 0001:40:01.1 hdma+, host#=11, fw=3.03.02 IPX kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. kernel unaligned access to 0xa0000002001c003e, ip=0xa0000001001ff370 kernel unaligned access to 0xa0000002001c0067, ip=0xa0000001001ff370 kernel unaligned access to 0xa0000002001c0075, ip=0xa0000001001ff370 kernel unaligned access to 0xa0000002001c0086, ip=0xa0000001001ff371 security: 3 users, 4 roles, 318 types, 20 bools security: 53 classes, 10823 rules SELinux: Completing initialization. SELinux: Setting up existing superblocks. SELinux: initialized (dev sda2, type ext3), uses xattr SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts SELinux: initialized (dev mqueue, type mqueue), not configured for labeling SELinux: initialized (dev hugetlbfs, type hugetlbfs), not configured for labeling SELinux: initialized (dev devpts, type devpts), uses transition SIDs SELinux: initialized (dev eventpollfs, type eventpollfs), uses genfs_contexts SELinux: initialized (dev pipefs, type pipefs), uses task SIDs SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts SELinux: initialized (dev pfmfs, type pfmfs), not configured for labeling SELinux: initialized (dev sockfs, type sockfs), uses task SIDs SELinux: initialized (dev proc, type proc), uses genfs_contexts SELinux: initialized (dev bdev, type bdev), uses genfs_contexts SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 Attached scsi CD-ROM sr0 at scsi1, channel 0, id 2, lun 0 tg3.c:v3.22-rh (February 11, 2005) ACPI: PCI interrupt 0000:00:01.0[A] -> GSI 28 (level, low) -> IRQ 50 divert: allocating divert_blk for eth0 eth0: Tigon3 [partno(A7109-60001) rev 0105 PHY(5701)] (PCI:33MHz:64-bit) 10/100/1000BaseT Ethernet 00:0e:7f:ed:62:60 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[0] ACPI: PCI interrupt 0001:00:01.0[A] -> GSI 132 (level, low) -> IRQ 58 divert: allocating divert_blk for eth1 eth1: Tigon3 [partno(A7109-60001) rev 0105 PHY(5701)] (PCI:33MHz:64-bit) 10/100/1000BaseT Ethernet 00:0e:7f:ed:62:81 eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[0] md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. ACPI: Sleep Button (FF) [SLPF] ACPI: Power Button (CM) [PWRB] EXT3 FS on sda2, internal journal device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm@uk.sistina.com SELinux: initialized (dev sda1, type vfat), uses genfs_contexts SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs kjournald starting. Commit interval 5 seconds EXT3 FS on sda5, internal journal EXT3-fs: mounted filesystem with ordered data mode. SELinux: initialized (dev sda5, type ext3), uses xattr kjournald starting. Commit interval 5 seconds EXT3 FS on sda6, internal journal EXT3-fs: mounted filesystem with ordered data mode. SELinux: initialized (dev sda6, type ext3), uses xattr kjournald starting. Commit interval 5 seconds EXT3 FS on sda3, internal journal EXT3-fs: mounted filesystem with ordered data mode. SELinux: initialized (dev sda3, type ext3), uses xattr kjournald starting. Commit interval 5 seconds EXT3 FS on sda4, internal journal EXT3-fs: mounted filesystem with ordered data mode. SELinux: initialized (dev sda4, type ext3), uses xattr Adding 20971488k swap on /dev/sda7. Priority:-1 extents:1 SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts